Configuration

This equipment consists of the following components.
1)  Spectratech OEG-17APD Main unit ---------------------------------------------- 1 set
2)  Spectratech OEG-17APD-00-D30 Sensor cable (Detector) ------------------------- 1 set
3)  Spectratech OEG-17APD-00-E30 Sensor cable (Emitter) -------------------------- 1 set
4)  Spectratech OEG-17APD-01-50 Light-blocking cap ------------------------------- 1 pc
5)  Spectratech OEG-17APD-02 Optical phantom ------------------------------------- 1 set
6)  Spectratech OEG-17APD-06 GEN-LOCK cable -------------------------------------- 1 pc
7)  Spectratech OEG-17APD-07 CD-ROM for Application software  -------------------- 1 pc
8)  Spectratech OEG-16-05 BOX for manual event trigger input  -------------------- 1 pc
9)  AC adaptor TR60M05-26E13　SINPRO --------------------------------------------- 1 pc
10) Operation manual  ------------------------------------------------------------ 1 set

Sensor palette, PC, and Network HUB are not included. Please purchase separately.
※ The component beginning with Spectratech OEG-16- is in common with Spectratech OEG-16

1) Spectratech OEG-17APD Main unit ------------------------------------------------------------------------- 1set

POWER :	Pressing the upper part of this switch turns on the power supply and the LED lights up in green.
MEMORY CARD :	The accompanying SD memory card can be inserted, and support ４GB, 8GB, 16GB, and 32GB. This SD memory card is used to reset the IP address of OEG-17APD when it was delivered or LAN connection was changed, etc. setting change in the payment time or the LAN access was done. (Resetting IP address is described in §2 of Software edition in detail.)
START :	Usually, a measurement/record is started by the command from PC not using this button.
STOP :	Pressing this button will stop a measurement/record. It is confirmed by the green LED lit up. It can be stopped also from PC.
EVENT :	This button is pressed when an event trigger is wanted to input manually from the front side of the main unit. It corresponds only during being measured. Another manual event trigger input is prepared also on the rear side of the main unit.
CAL :	This button is for the biological calibration, and not usually used because it is performed from PC usually. The LED is flashing in green during a calibration, and when it ended and all the channels have become in green (proper signals), it is possible to measure. The signal is not proper at some of the channels when it lights up in orange. However, a record can be begun. When it lights up in red, the signal is not proper at all the channels. When it lights up in orange or red, please confirm the mounting condition of the sensors to the living body, and try the calibration again.

LED display

FINE:	It lights up in green in FINE mode, and turns off in FAST mode.
GEN-LOCK:	It lights up when the OEG-17APD is being synchronized with another OEG-17APD as the master.
BATT-1:	Not used.
BATT-2:	It lights up in red when the capacity of the internal button battery for the calendar clock fell less than the specified value. In such case, please replace it with a new battery soon.
MEMORY:	It lights up in red when the capacity of the SD-MEMROY fell less than 100MByte.
PD1 - PD6:	It lights up in green when each biological signal input to PD1-PD6 is in the proper range. It lights up in orange to warn for an excessive input. When the sensor doesn't stick to the living body firmly, this phenomenon will come out in most of cases. You can measure as it is when it lights up in green as the calibration result described in §11. However, it lights up in orange, please reconfirm the mounting condition of the sensors to the living body, and use it in the condition of lighting up in green as much as possible.

DETECTOR:	The accompanying Spectratech OEG-17APD-00-D30 Sensor cable (DETECTOR) is connected.
EMITTER:	The accompanying Spectratech OEG-17APD-00-E30 Sensor cable (EMITTER) is connected
EXT-EVENT-IN 1:	This is used as a measurement/record start input or an event trigger input from the outside via the optional Spectratech OEG-16-04 BNC cable for the external signal input. The button type battery for the photo isolation has to have been mounted to use this input. It is shipped with the battery mounted, and its lifetime is about 3-5 years.
EXT-EVENT-IN 2:	This is used as an event trigger input from the outside via the optional Spectratech OEG-16-04 BNC cable for the external signal input. The button type battery for the photo isolation has to have been mounted to use this input. It is shipped with the battery mounted, and its lifetime is about 3-5 years.
REMOTE:	Cable from the accompanying Spectratech OEG-16-05 BOX for manual event trigger input is connected. It is also possible to input an event trigger manually from the BOX. When an event trigger is accepted, the green LED on the BOX lights up.
ANALOG-IN1, 2, and 3:	This is the general-purpose analog signal input terminal, which can be measured simultaneously with the biological signal (hemoglobin change signal). It is convenient to measure simultaneously with sphygmograph and thermometer, etc. which has an analog signal output function. Input voltage range: 0 to +5V (High impedance input) Number of input channels: 3 Resolution: 12 Bit Sampling interval: Identical to the biological signal’s sampling interval (0.65535 or 0.08192 sec)
ID-SW:	This is used to identify this equipment in case of the stackable connection. The default value is 0. It will select the value of 1, 2, 3, ･ ･ ･ in order of the stackable connections.
100Base-T:	This is used when it is connected to PC to monitor via wired 100M-ethernet.
DC-IN+5V:	DC output terminal from the accompanying AC adaptor TR60M05-26E13 SINPRO is connected.
T1:	It is the terminal for connect to another OEG-17APD for the stackable connection.
Battery Box:	It is the Battery Box for internal calendar clock and photo isolation part.
GENLOCK-IN:	This terminal is used for the stackable connection of 2 or more OEG-17APD main
GENLOCK-OUT:	units. The standard GEN-LOCK cable is used in case of the stackable connection.

2) Spectratech OEG-17APD-00-D30 Sensor cable (DETECTOR) -------------------------------------- 1set

3) Spectratech OEG-17APD-00-E30 Sensor cable (EMITTER)  ----------------------------------------- 1set

4) Spectratech OEG-17APD-01-50 Light-blocking cap  --------------------------------------------------- 1pc

5) Spectratech OEG-17APD-02 Optical phantom ----------------------------------------------------------- 1set

6) Spectratech OEG-17APD-06　GEN-LOCK cable -------------------------------------------------------- 1pc

7) Spectratech OEG-17APD-07 CD-ROM for Installation software ----------------------------------- 1pc

8) Spectratech OEG-16-05 BOX for manual event trigger input (with 3m-long cable)  -------- 1pc

9) AC adaptor   TR60M05-26E13　SINPRO  ----------------------------------------------------------------- 1pc

10) Operation manual----------------------------------------------------------------------------------------------- 1set

 

 

To top of page

Return